- 3 Jan 2015
- 288
- 67
Hennessy Rom by LoXaR and parfetto cooperation test - Xiaomi.eu with Root to flash by Flash tool, 100% working.
Thanks to:
Xiaomi.eu , LoXaR and Igorphoenix for that . Specialy thanks to LoXaR for this greate work.
Use SP Flash tool from the ZIP.
Go to Download tab.
Choose Download agent - DA_SWSEC.binfrom SP Flash folder.
Choose Scatter - MT6795_Android_scatter.txt from imagesfolder
And finally and very important -UNCHECKpreloader (if don't - you are going to brick RMN3)
Then flash as usual with SP Flash:
Select Download Onlyoption.
Press Download button.
Turn off RMN3.
Press vol down and powerbuttons on RMN3 and plug USB cable immediately (while black screen, if fastboot picture appered - turn off RMN3 and try again).Keep buttons pressed.
See the red bar in SP Flash.
See the yellow bar in SP Flash - that means flashing is started, unpress buttons on RMN3 and wait until progress is 100% and window with green check mark appear. Flashing is done.
Now disconnect USB cable, close the SP Flash and turn on RMN3. First start may take up to 10 minutes.
**************
I flashed over official chinese DEV ROM 6.1.11 without issues. Works fine for me.
BEFORE flashing this xiaomi.eu ROMto avoid any possible bugs. The manual is here - http://en.miui.com/thread-193681-1-1.html.
*****************************
First step, install this 2 drivers in your PC.
https://mega.nz/#!sIkxEYoI!TnWqWCsx3F_2Y6F86PSNttr8jKVFFz6xCOuJrnsU-ME
After many tests we see the Rom can be flashed over any other Base Rom.
To begin with no errors install that one 6.1.14 and untick only the PRELOADER
https://mega.nz/#!uZBjET5C!jmqXQIR-1iCeubRQGTv8mdznZRJXIfloqQzLNq3zWYc
Untick preloader to not brick your phone.
After first Rom flashed make a factory reset.
Now you are in xiaomi.eu rom flash only the System.
New update 6.1.21. (Recommended)
https://mega.nz/#!vNxUwKCa!25oCnLtSSzXHTTZ0iQuSx3NSKHHBBb7zfsVOYlVksXI
New update 6.1.29. (Many people says it have some lags and errors, so we dont recommend it)
https://mega.nz/#!cJkhhByZ!JYVNYHLUpR_YZtW7XE8mpQJDHTuLziENlfIgCnL7aus
New update last week Rom, 6.4.7
https://mega.nz/#!kENmXKAC!-klhQ0geUd3hc2lWjk2TNmUrlgTJScnd4BIGXff5On4
Allways untick PRELOADER.
**********NEW**********
Stable Rom7.2.3 xiaomi.eu/JamFlux to locked and unlocked bootloader.
Thanks to jamFlux for this great work
https://www.androidfilehost.com/?fid=24438995911970690
That rom is base stable, so need to flash it all, except bootloader, unless you are already in stable 7.1.8, in that case can flash only system.
Flash only the SYSTEM, if you are in xiaomi.eu DEV Rom already untick all the rest.
Thanks to:
Xiaomi.eu , LoXaR and Igorphoenix for that . Specialy thanks to LoXaR for this greate work.
Use SP Flash tool from the ZIP.
Go to Download tab.
Choose Download agent - DA_SWSEC.binfrom SP Flash folder.
Choose Scatter - MT6795_Android_scatter.txt from imagesfolder
And finally and very important -UNCHECKpreloader (if don't - you are going to brick RMN3)
Then flash as usual with SP Flash:
Select Download Onlyoption.
Press Download button.
Turn off RMN3.
Press vol down and powerbuttons on RMN3 and plug USB cable immediately (while black screen, if fastboot picture appered - turn off RMN3 and try again).Keep buttons pressed.
See the red bar in SP Flash.
See the yellow bar in SP Flash - that means flashing is started, unpress buttons on RMN3 and wait until progress is 100% and window with green check mark appear. Flashing is done.
Now disconnect USB cable, close the SP Flash and turn on RMN3. First start may take up to 10 minutes.
**************
I flashed over official chinese DEV ROM 6.1.11 without issues. Works fine for me.
BEFORE flashing this xiaomi.eu ROMto avoid any possible bugs. The manual is here - http://en.miui.com/thread-193681-1-1.html.
*****************************
First step, install this 2 drivers in your PC.
https://mega.nz/#!sIkxEYoI!TnWqWCsx3F_2Y6F86PSNttr8jKVFFz6xCOuJrnsU-ME
After many tests we see the Rom can be flashed over any other Base Rom.
To begin with no errors install that one 6.1.14 and untick only the PRELOADER
https://mega.nz/#!uZBjET5C!jmqXQIR-1iCeubRQGTv8mdznZRJXIfloqQzLNq3zWYc
Untick preloader to not brick your phone.
After first Rom flashed make a factory reset.
Now you are in xiaomi.eu rom flash only the System.
New update 6.1.21. (Recommended)
https://mega.nz/#!vNxUwKCa!25oCnLtSSzXHTTZ0iQuSx3NSKHHBBb7zfsVOYlVksXI
New update 6.1.29. (Many people says it have some lags and errors, so we dont recommend it)
https://mega.nz/#!cJkhhByZ!JYVNYHLUpR_YZtW7XE8mpQJDHTuLziENlfIgCnL7aus
New update last week Rom, 6.4.7
https://mega.nz/#!kENmXKAC!-klhQ0geUd3hc2lWjk2TNmUrlgTJScnd4BIGXff5On4
Allways untick PRELOADER.
**********NEW**********
Stable Rom7.2.3 xiaomi.eu/JamFlux to locked and unlocked bootloader.
Thanks to jamFlux for this great work
https://www.androidfilehost.com/?fid=24438995911970690
That rom is base stable, so need to flash it all, except bootloader, unless you are already in stable 7.1.8, in that case can flash only system.
Flash only the SYSTEM, if you are in xiaomi.eu DEV Rom already untick all the rest.
Last edited: